三级片视频播放,精品三级片在线观看,A级性爱视频,欧美+日韩+国产+无码+小说,亲子伦XX XX熟女,秋霞最新午夜伦伦A片黑狐,韩国理伦片漂亮的保拇,一边吃奶一边做边爱完整版,欧美放荡性护士videos

| 注冊| 產品展廳| 收藏該商鋪

行業產品

當前位置:
廣東宏展科技有限公司>>技術文章>>ASTM D470-99測試標準

產品分類品牌分類

更多分類

ASTM D470-99測試標準

閱讀:1267        發布時間:2018-7-20

本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用,為確保測試結果的準確性、節省您的時間,如需ASTM D470-99標準詳細信息或ASTM D470-99具體測試方法,與我們技術人員聯系或給我們留言,我們將為您相關的技術支持。

ASTM D470-99標準介紹

簡介

ASTM  D470-99是交聯絕緣材料和電線\電纜外皮的老化測試標準。標準后續的數字指代標準的采用年限,或者修訂情況下后確定修改的年份。

1. Scope

1.1 These test methods cover procedures for testing crosslinked insulations and jackets for wire and cable. To determine the test to be made on the particular insulation or jacket, reference should be made to the product specification for that type. These test methods do not apply to the class of products known as flexible cords.

1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 4.

1.3 Whenever two sets of values are presented, in different units, the values in the first set are the standard, while those in the parentheses are for information only.

1.4 In many instances the insulation or jacket cannot be tested unless it has been formed around a conductor or cable. Therefore, tests are done on insulated or jacketed wire or cable in these test methods solely to determine the relevant property of the insulation or jacket and not to test the conductor or completed cable.

1.5 The procedures appear in the following sections:

AC and DC Voltage Withstand Tests 22 to 29
Capacitance and Dissipation Factor Tests 38 to 44
Cold Bend 128
Cold Bend, Long-Time Voltage Test on Short Specimens 51 to 57
Double AC Voltage Test on Short Specimens 45 to 50
Electrical Tests of Insulation 17 to 64
Heat Distortion Test 127
Horizontal Flame Test 100 to 104
Insulation Resistance Tests on Completed Cable 30 to 37
Mineral Filler Content, Determination of 111 to 115
Ozone Resistance Test 87 to 99
Ozone Resistance Test 87 to 99
Partial-Discharge Test 58 to 64
Physical Tests of Insulation and Jacket Compounds 5 to 16
Surface Resistivity Test 116 to 120
Track Resistance Test 129 to 132
U-Bend Discharge Test 121 to 125
Water Absorption Test 65 to 71
Water Absorption Test, Accelerated 72 to 86
Water Absorption Test on Fibrous Coverings 105 to 110

 

2. Referenced Documents

2.1 ASTM Standards: D 149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies2

D 150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulating Materials2

D 257 Test Methods for D-C Resistance or Conductance of Insulating Materials2

D 412 Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermostatic Elastomers—Tension3

D 454 Test Method for Rubber Deterioration by Heat and Air Pressure3

D 572 Test Method for Rubber Deterioration by Heat and Oxygen3

D 573 Test Method for Rubber—Deterioration in an Air Oven3

D 1193 Specification for Reagent Water4

D 1711 Terminology Relating to Electrical Insulation2

D 2132 Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials2

D 3755 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Under Direct-Voltage Stress5

D 5025 Specification for a Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials6

D 5207 Practice for Calibration of 20 and 125 mm Test Flames for Small-Scale Burning Tests on Plastic Materials6 D 5423 Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation

2.2 ICEA Standard:

T-24-380 Guide for Partial-Discharge Procedure7

 

3. Terminology

3.1 Definitions—For definitions of terms used in these test methods, refer to Terminology D 1711.

3.2 Definition of Term Specific to this Standard:

3.2.1 aging (act of), n—exposure of material to air or oil at a temperature and time as specified in the relevant material specification for that material.

3.3 Symbol:

3.3.1 kcmil—thousands of circular mils.

收藏該商鋪

登錄 后再收藏

提示

您的留言已提交成功!我們將在第一時間回復您~
二維碼 意見反饋
在線留言
主站蜘蛛池模板: 运城市| 嘉善县| 马山县| 唐山市| 曲阳县| 旌德县| 西盟| 佛坪县| 武宣县| 大城县| 绥芬河市| 康马县| 荆州市| 斗六市| 江津市| 海兴县| 如皋市| 行唐县| 宣恩县| 龙里县| 海伦市| 沂水县| 黄山市| 建昌县| 大丰市| 商河县| 兴国县| 宿松县| 石屏县| 泾阳县| 通榆县| 哈密市| 贵港市| 牙克石市| 普定县| 余庆县| 乡宁县| 彰化市| 略阳县| 孟州市| 瑞昌市|